What Different Options Are Available For Enhancing The Range Of Home WiFi Signal?

All your online work or business depends on the internet. The faster it is, the lesser will be the time taken. However, the speed of the internet doesn’t remain constant throughout the house. For this, you can either use the range extender or extend the power line. The functioning of the range extender is dependent on its position and placement. Though the power line has advantages over the range extender, at the same time it is much expensive as compared to the range extender.

Understand how these devices work

When we perform the Netgear extender setup to connect it to the router of an existing network, then it strengthens the signal and expands it to the areas where there was the least signal earlier. The extender receives the signal from the router and re-transmit it. The router settings remained unchanged but with increased network strength.

As we have discussed the power line increases the signal strength through electricity. In this, there are two parts mainly, one part of which is connected to the router’s Ethernet, and the second one is connected to the place where you want to increase the coverage of your Wi-Fi.  The signal is then transmitted to the wires through the wires with the least interference. This ensures fast and reliable transmission between the devices. If you don’t know anything about powerline or range extender, then you must contact the experts.

Coverage area

The purpose of adding the extender to the network is to make the Wi-Fi signal possible in the dead zones or the dead corners of your house. A single router alone can’t provide the signal in all directions. So, this is where the extender comes to its place.

The placement of a device plays an important role when it comes to receiving a good quality signal. If you have placed the router in the living room, then the extender should also be placed in the same room. After the device gets configured, you can place the extender anywhere inside the home.

The power line on the other hand is recommended for having internet connectivity in a particular room. The signal through the power line is free from interference that occurs due to the walls or furniture. The average range of the powerline is approximately 300 meters.

Remember, don’t forget to check the quality of the internet available at home. The internet service provided by the internet service provider at home must be capable of delivering a min of 1 Mbps of data. If the speed of the internet is slow, then you have to go with a wireless range extender.

There are many range extender models available in the market. You need to select the one with more than one frequency band and 2 top antennas affixed.  There are many manufacturers in the market for range extenders but selecting the right brand can be a cumbersome project for an individual having limited knowledge. You can check the Netgear range extenders having the proper speed and coverage.

How To Configure The Wi-Fi Network Of An Extender Or Access Point To Automatically Connect To The Best Signal

When you opt for the Internet with a reputed ISP, they usually offer us a Wi-Fi router for free through which to connect both computers and other devices to the Internet, cable, and Wi-Fi. However, these routers, in general, are of very low range, so, in addition to not having many functions and being of very low performance, both the speed and the coverage of the Wi-Fi network usually leave quite a lot to wish.

While solving the problem of speed is quite complicated and happens to change the router or add another that takes care of Wi-Fi, if you are only interested in solving the problem of wireless network coverage. One of the simplest ways to solve it is by installing a WiFi extender or access point, a device that, placed where the router’s signal arrives well but begins to get lost, is responsible for repeating it so that it reaches the areas farthest from the router.

Depending on the device you install, it is possible that it directly copies the Wi-Fi data that must be repeated and forwards the signal as such, or that you have to configure the network manually to which you connect (Wi-Fi access point).

In the first case, you will not have to do anything, so simply connecting the device and linking it to the original router would already be repeating the signal with the same configuration as our router, however, if what you have installed has been a point of access, before making it work you must do the following.

How to create a Wi-Fi hotspot

The first thing to do is to access its configuration panel by connecting it directly by cable to the computer and accessing its IP from the browser.

Once inside the configuration panel, you must place yourselves on the Wi-Fi configuration section, and there you must configure the options as follows:

  • SSID or network name: The same on the router and access point.
  • Security, password, and encryption: The same on both devices.
  • Channel: Different on the router and access point.

Once you save the changes, you can see that now, although computers and mobiles show us a single network (the closest one), if you scan the wireless spectrum you can see that, in reality, there are two equal networks on different channels.

If you are using an Android/iOS smartphone or tablet, this device will automatically connect to the network that offers the best signal. If you are closer to the main router, you will connect to it, but if you move away, you will connect without having to walk to the access point. In case of using a Windows laptop, this system does not get along with network changes, so you will most likely have to disconnect and connect again to choose the network that arrives with the best signal depending on where you are.

If you configure the network incorrectly, although the configuration is most likely to work, surely you have two independent Wi-Fi networks so that you have to switch from one to another manually. This will happen if, for example, the two networks have different SSIDs or different passwords. If you configure them with the same channel, it will most likely not work since mobile devices will not know how to interpret the change.

WiFi Extender Or Mesh Router – Which Suits Your Requirements The Best?

A discussion has picked up regarding the difference between Wi-Fi Range Extender and Mesh Router with the inception of the latter into the tech world. A decade ago, when Wi-Fi Routers became prevalent, users were excited to access the internet without using any wires and cables, but then, the same users felt the need of internet in every nook and cranny of the house, hence gave rise to extenders.

WiFi Range Extenders were good; no… actually, they were great because they allowed users to connect to the internet from any corner of the house. The only downside to WiFi Range Extenders was their range, which wasn’t that great. A WiFi Range Extender is excellent in covering a small house with 2-3 rooms, but for bigger homes, the dead spots may continue to exist.

To overcome this problem, the bright minds of this world sat together and brainstormed on what new can be delivered to users to ensure uninterrupted internet connectivity throughout their homes without changing the network. This led to the discovery of ‘Mesh Router’, a revolutionary device, which can overcome the problem of dead spots in large homes. The functioning of mesh routers is very different from WiFi Range Extenders. Where the role of an extender is to boost the internet signal it receives from the router, Mesh Router on the other hand creates a seamless network all around the house.

A mesh router is not a single device, but it is a group of 3-4 devices out of which, one device works as a hub and other as nodes. You need to place the hub at a central location, whereas the nodes in all corners of the house, so as to cover the entire area with internet. A notable feature of the mesh router system is that you receive immaculate internet throughout the premises without changing the network, which means, you remain on a single network but receive the best internet signal from the closest node.

Which is better? A WiFi Range Extender or Mesh Router?

Well, both devices are used in different setups. Where a WiFi Range Extender is used for small houses, mesh routers are suitable for large houses. Moreover, the technology incorporated in mesh routers is more advance compared to what is included in WiFi Range Extenders. It all boils down to personal preference as to what a user really wants. Netgear offers the best of both worlds, i.e., it has the best WiFi Range Extenders as well as Mesh Routers, so you can consider getting a product of this company. Or, if you have another company in mind, then you can opt for it.

How To Get Most Out Of Your Netgear Wi-Fi Nighthawk EAX80 Mesh Extender?

With this post, we will try to make you understand the working of range extender and how they can be best employed. We are going to consider Netgear Nighthawk EAX80 mesh range extender in this post. Nighthawk series is considered as expensive and most-featured series of Netgear networking products. With AX8, 8 here refers to the capacity of the range extender to transmit the same signal to 8 devices at a time. Being a new Wi-Fi standard, it is currently being supported by limited Wi-Fi devices like Intel cards and Samsung S10 series phones. The range extenders mainly boost the existing network reaching your home from the internet service provider’s end. If you are receiving a signal up to 5 meters inside your home and want to reach it up to 10 meters, then you can go with a range extender that acts as an amplifier for the network.

Range extenders explained

In this modern world, most of our day to day work depends on the connectivity to the network. All the consumer durable we use either in office or at home requires a stable internet connection for optimal functioning, And this is possible only if there is equal signal strength distributed on all the devices at the same time. This is where the Wi-Fi extender comes into place, as it can handle multiple Wi-Fi devices simultaneously. If you employ EAX80, it can boost the signal of every standard router, no matters which brand the router is from. Let us explain the whole of working simply. If you are a senior citizen, then the speed requirements will be comparatively lesser than that of the photographer. The signal enters the home through the modem provided by the internet service provider. A basic router can transfer data at a rate of 100mbps.

How to use the wireless range extender like EAX80 in the best way?

Now, you must have understood what the range extender is, we would now suggest to you how you can use the range extender more efficiently. The simplest method to improve the signal strength of your Wi-Fi is by restarting the Wi-Fi router and plug-in back after some time and try connecting the Mesh Wi-Fi system instead of the normal extender.

Our technical experts have already tested and verified the performance of the AX8 nighthawk wireless router and find that it is offering the high signal strength in all the directions irrespective of a particular zone or area. You can use Wi-Fi 6 speed instead of using a slower 5/AC mesh system.

The Netgear Nighthawk AX8 or 6 is 6 & 8-stream mesh extender by Netgear will meet your expectations and you can easily come out of the situation where you are not being able to connect to the internet from different Wi-Fi devices. When you connect the Nighthawk WiFi 6 mesh extender to the power supply and the network port, it will start connecting to the existing network on its own. You don’t need to search for the router’s SSID manually. Once connected, you can get the same speed of network on all the floors of your house.

All-New Range Extender 1200 MBPS With Ethernet Port, Alexa, And Smart Devices Support

In the times of COVID Epidemic, the companies are trying their best by offering the products that can best suit the requirements. In the latest updates, the wireless range extender has been launched having 1200 Mbps data transfer speed. You can connect the smart devices like Samsung, PC, 4K streaming devices simultaneously with this range extender without compromising with the speed.

Coming to its characteristics or unique features:

  1. Universal compatibility: The most exciting feature is its universal compatibility. You can connect the extender to any router or AP, thus enhance the network strength for 2.4 GHz. The 1200 Mbps dual-band Wi-Fi is compact, reliable and can be easily configured. It even add aesthetics to your home décor.
  2. Easy to install: There’s a simple button given on the hardware named ‘WPS button’ by pressing which you can easily configure in 8 seconds. Another way of How To Set Up WiFi Extender  is by using the web-based setup which can be opened by entering the IP address on the internet browser. Once installed, you can place the range extender anywhere inside the home and start getting the proper signal strength in every corner of it. There’s an option to connect the Wi-Fi devices either wirelessly or physically with the extender.
  3. Eliminate dead zones: Usually, the router employed with the home network is not capable of covering the whole house or area of the floor. The restroom, garden, and balcony remained dead zone for the network. The new extender has a smart LED that helps you decide the placement of an extender at the best location. It supports WPA/WPA2 PSK and hidden SSID to avoid unauthorized access by hackers and strangers.
  4. Guaranteed satisfaction: In case you are not being able to set up or use the extender efficiently, then a team of professionals is available 24×7 for help and support. If you are having any problem or issue to discuss, you can reach through a toll-free number. They will try to satisfy the customer by putting their full potential in other words, you can say satisfaction is guaranteed.

Wifi Range Extender Or Mesh Router – Which Suits Your Home Network The Best?

With most people spending time at home these days, the requirement of the internet has risen exponentially, as everybody needs the internet to keep themselves entertained at this time of global emergency. People are forced to work from their homes using their computers and they require the internet at all times. With most homes having Wi-Fi networks, there is a problem that has come to the fore, which was somewhat hidden when things were normal.

The problem is that the Wi-Fi signals are limited to certain areas and people sitting beyond those areas are not able to access the internet. If you too are experiencing this particular issue, i.e., dead zones in some spots of your house, then you have a few options to eliminate dead zones such as WiFi Range Extender or Mesh Router, which has its own range-extending satellite devices known as nodes.

WiFi Range Extenders are the cheap and best option for smaller spaces, but if you have a big home, then you will have to opt for a mesh router because they can offer a comprehensive coverage through their nodes, which you can strategically place in different areas of the house. The only thing that matters in wireless networking is ‘Location’ because the wireless access points can only put out a network signal, which is equally strong as the incoming wireless signal that is being received from the router.

The best way is to check at the speed test data and then, finding the room closest to the dead zone where the internet signals are good. Doing this will help you find the right place for having the extender to cover the dead zone. It is always great to run a test speed on your network to know how much speed you are getting.

Use WiFi Range Extender for small dead zones

If you are living in a small house with two rooms, then you just need a WiFi Extender to extend the range of your wireless signal, and you can easily get an extender online. Check out the steps to know how to set up a WiFi Extender. Before buying an extender, just make sure it has the WPS button because that makes the setup process a lot easier. The drawback in almost all WiFi Extenders is that they don’t get to the max speed of your internet network, so you are going to get 50Mbps – 75Mbps, which is sufficient for online HD streaming, playing online video games and do other tasks. Just keep in mind that you need to find the room closest to the dead zone with the best internet signal because you’ll place the extender at that spot.

Use Mesh Routers for whole-home coverage

If there are multiple dead zones in your house, then you have to get a mesh router, which comes with nodes that you can place in different spots of the house to ensure that the entire house receives the best internet signals. The software of these mesh routers has a huge role to play in the functioning and setting up the algorithms to calculate the best way to route your connection as per your movements in the house. As you move from the range of one node to another, the premium-quality mesh router will automatically transfer your network to the strongest node without letting you know.

It is now up to you to decide whether you need a WiFi Extender or a mesh router. There is obviously a price difference between the two, as an extender will cost you 5x less than what a mesh router will, but then, the requirement plays a major role because an extender may not be able to cover a large house.

How To Access Internet Via Netgear WiFi Extender During Coronavirus Lockdown?

COVID-19 or Coronavirus as it is popularly called has brought the whole world on its knees. The entire world is under lockdown with thousands of people dying every day. The only way to work is by staying at home, which is why the importance of the internet has risen exponentially. I’m not saying it wasn’t before, but the internet is more important today than it ever was, as it is the only source of doing business or should I say, retaining business for people until the SARS CoV-II virus fully vanquishes.

The good thing is that in most parts of the world, the internet speed and quality are at satisfactory levels. At the same time, it can also be said that businesses that used to be carried out over the internet are the ones that are still being carried out, while others are being in shambles.

If you too are forced to sit inside your house and work on the internet, then that is better than sitting idle at home. However, many users are facing issues while accessing the internet due to signal range related issues. As many people only have routers at homes, which have a limited range, the issue is quite common to arise. If you want to get rid of this issue, then you got to install a WiFi Extender to extend the range of the Wi-Fi signals. You can buy N300 Extender because of its easy setup and incredible range and consistency. To know how to the steps for the Netgear WiFi Extender N300 setup, you can follow this link. The process is very simple and can be performed even by non-technical people.

When it comes to setting up an extender, you must keep in mind that there is a software aspect of the process as well. You will have to download Netgear Genie followed by performing Netgear Genie Smart setup, which involves entering the user credentials.

You need to know that Netgear Genie setup allows you to manage and control your extender in the easiest of ways, so make sure you have the app installed on a device where you can easily access it. Once you have configured your extender with Genie app, you can connect your devices with the extender’s network and you shall surf the web without any issues. Should you come across any issue, then you can get in touch with experts for quick and reliable assistance.

Answering Questions Related To Extender, Genie App, Default IP And Much More

How To Login To Extender After Performing Netgear Genie Smart Setup Wizard?

Once you have configured your extender with Genie Smart Setup Wizard, you can easily login to extender by using the username and password given on the extender device. If those details are not working, then you should click here.

Router Is Using WEP Security Protocol, Can I Connect My Extender To The Router Using WPS Method?

WPS is a much better security protocol that makes use of complex passwords to safeguard a network, whereas WEP is an older technology that is susceptible to hacking. So, if your router’s security is WEP and you want to use the WPS method to connect your extender to the router using WPS, then you will have to make changes in the Netgear Genie app. For more details, click on this link.

What Is The Process Of Configuring Your Netgear Wifi Extender N300 Using The Netgear Installation Assistant?

There are different ways of configuring WiFi Extender N300, and if you have opted for the installation assistant method, then you must have a LAN cable and a working internet connection to follow the steps, details of which you can find on this webpage.

How To Access 192.168.1.250?

192.168.1.250 is the default IP address of Netgear Extender and if you want to setup your extender properly, then you must access the web interface of the extender, which you can access by entering www.mywifiext.net or www.mywifiext.local for Windows and Mac computers respectively. If both URLs are not working, then you should enter 192.168.1.250 in the address bar. To know more, click here.

7 Reasons Why Your Netgear WiFi Range Extender Not Setting Up

There could be dozens of reasons for not being able to set up a WiFi Extender, but if you want to know the 7 most common reasons along with their solutions, then you should check out this link.

How To Setup Netgear Wifi Extender?

If you want to enjoy fast and uninterrupted internet in every nook and cranny of the house, then you must know how to properly set up Netgear WiFi Extender. There is a certain process that you need to follow, details of which, you can find by going to this site.

How To Configure Netgear Range Extender Using Netgear Genie Smart Setup?

If you want to control your extender from your smart device, then you have to configure it without Genie Smart Setup. There is a series of steps that you need to perform to configure extender with Genie, which you can take a look at by going to this link.

Getting Problem Connecting The Netgear Range Extender To iPhone?

If you are unable to connect your WiFi Range Extender to iPhone, then you might be entering the wrong password for the network. Or, there could be some other issue with the extender or the network. Whatever the issue, it can be easily fixed by visiting this link.

How To Get Fast And Reliable Internet In Every Corner Of The Room?

If the internet is not available in every corner of the room, then there is no benefit of buying an expensive internet plan. If there are areas in your house or office where internet signals are absent, then you should install a WiFi extender. To know how to get fast and reliable internet, click here.

How To Download And Setup Netgear Genie App?

Check out the steps on how to download and setup the Netgear Genie app. Without this app, managing your extender will be very difficult, so make sure you get this app on your smart device.

How To Install Netgear Ex2700 With Firmware Above 1.0.1.8?

To ensure the proper functioning of your Extender Ex2700, you must check the firmware version of the device. If it is working on a firmware below 1.0.1.8, then you should check out this link to know how to install Netgear Ex2700 with firmware later than 1.0.1.8.

A Few Important Questions Answered Related To Wifi Range Extender

How To Get Rid Of Login Problem Of Netgear Range Extender?

To fix login problem in WiFi Range Extender, you must ensure that the username and password are correct. If the details are correct, then make sure that the internet connection is working properly. In case, both login details and internet connection are working properly, yet you’re not able to login, then you should ask experts for assistance. For that, click here.

How To Connect The Netgear Range Extender To Xbox 360 Gaming Console?

Net Gear Extender can connect to a wide range of operating systems, which include Xbox 360 Game Console as well, but there are certain steps that you need to perform, details of which you can get after clicking on this link.

How To Configure WN2500 Wireless Range Extender?

WN2500 wireless Range Extender is one of the most popular extenders that are used by thousands of customers. If you are looking to configure this extender, then you should follow the steps provided on this webpage.

How To Configure Your Netgear Wifi Extender N300 Using The Netgear Installation Assistant?

The process of configuring Netgear Extender N300 using Netgear installation assistant involves doing basic setting up of the extender and then, going to www mywifiext net link on the web browser of computer and make changes there. To know more about this process, you can visit this link.

How To Enhance The Signal Strength Of Network Using The Netgear Range Extender?

An extender is meant to enhance the strength and range of internet signal, but that can only be done if the extender is set up in the right way. To know the exact steps of setting up and configuring a Wi-Fi extender, follow this weblink.

How To Setup The Netgear Ex2700 In Bridge Mode?

Netgear Ex2700 can be set up in bridge mode, which is done to eliminate the need of placing the extender close to the router. To set up your extender in bridge mode, you need to follow certain steps, details of which you can find by going through this link.

What To Do If The SSID Of Range Extender Is Not Detected By Wireless Devices?

If you are dealing with this particular problem, then you need to refresh the extender setup page. Also, go through the settings of your extender to see if all the devices that you have connected to the extender are actually connected or not. In case, everything is fine, yet the issue persists, then click here to find the right solution.

How To Get Rid Of Netgear Login Problem If Not Accessible Through Mywifiext.Net?

Not being able to access the default address of extender is indeed a big problem, but it is not that common to see mywifiext.net link becoming inaccessible. If you are not able to log into the web interface of your extender, then visit this website to fix the issue.

Steps For Netgear Genie Smart Setup?

Netgear Genie is a software that allows you to configure multiple extenders for better control. Moreover, you can manage and control all your extenders from a single platform named Netgear Genie. However, to do all that, you must know the steps for Netgear Genie Smart Setup for which, you can check out this page.

How Do I Set Up My NETGEAR Wifi Range Extender N300 Setup?

To be able to set up a Wi-Fi Extender successfully is a big thing, as it gives you the opportunity to access the internet in any nook and cranny without any issue. If you want to know how to set up N300 Extender in the simplest of ways, then follow this link.

Frequently Asked Questions About Mywifiext.net, Netgear Extender & Genie

Troubleshooting Issues Connecting To mywifiext.net?

Mywifiext.net is a local address and not a regular internet website. It is used to open the settings of Netgear Genie or Smart Wizard. If mywifiext.net is not connecting, then check if you are connected to the internet via an Ethernet cable or wirelessly. If you are still not able to connect to mywifiext.net, then click here.

How To Login Netgear Wifi Range Extender?

To login to your Netgear WiFi Range Extender, you need to visit www.mywifiext.net or www.mywifiext.local in your address bar if you are using Windows or Mac computers respectively. Alternatively, you can enter https://192.168.1.250 in the address bar as well. Enter values in the username and password fields, which you can find at the back or bottom of the extender. If you are experiencing issues while logging into your extender’s web interface, then check this link.

How You Can Access 192.168.1.250?

The default IP address of your Netgear WiFi Extender is 192.168.1.250, and if you are not able to access it, then make sure that the extender is properly configured with the router. Also, check that the internet connection is active on the extender. If you are still not able to access this IP address, then click here to know more.

How To Fix Problem Of Connecting Mycloud To Netgear Ex2700?

After you configure Netgear Ex2700 properly, you can easily connect MyCloud with it, but in case, you are facing issues doing the same, then you need to identify the reason(s) behind the problem. To know more about the problem, check out this link.

How To Configure Wifi Extender Using Netgear Genie App?

Netgear Genie app is a specially designed application dedicated to controlling WiFi Extender. But, in order to manage and control your extender through the app, you should configure it first. There are some easy steps to configure Genie with Extender, details of which, you can get by opening this link.

How Can You Find The Steps For Netgear Extender Setup?

In order to enjoy the functionality of the Netgear Extender, you must set it up in the right way. While there is nothing complicated when it comes to Extender setup, but yes, you will have to follow certain steps. To know details about those steps, click here.

How To Configure The Netgear Range Extender N300 Using The Web GUI?

You need to configure your extender with the help of web GUI to easily manage and control the device. If you want to know the exact steps of configuring Extender N300 using Web GUI, then click on this link.

How Do I Setup My Netgear Genie Extender?

Follow this link to find out the exact steps for setting up Netgear Extender in the most suitable way. In case, you encounter any issues during the setting up process, then you can reach out to experts for the best assistance.