What Different Options Are Available For Enhancing The Range Of Home WiFi Signal?

All your online work or business depends on the internet. The faster it is, the lesser will be the time taken. However, the speed of the internet doesn’t remain constant throughout the house. For this, you can either use the range extender or extend the power line. The functioning of the range extender is dependent on its position and placement. Though the power line has advantages over the range extender, at the same time it is much expensive as compared to the range extender.

Understand how these devices work

When we perform the Netgear extender setup to connect it to the router of an existing network, then it strengthens the signal and expands it to the areas where there was the least signal earlier. The extender receives the signal from the router and re-transmit it. The router settings remained unchanged but with increased network strength.

As we have discussed the power line increases the signal strength through electricity. In this, there are two parts mainly, one part of which is connected to the router’s Ethernet, and the second one is connected to the place where you want to increase the coverage of your Wi-Fi.  The signal is then transmitted to the wires through the wires with the least interference. This ensures fast and reliable transmission between the devices. If you don’t know anything about powerline or range extender, then you must contact the experts.

Coverage area

The purpose of adding the extender to the network is to make the Wi-Fi signal possible in the dead zones or the dead corners of your house. A single router alone can’t provide the signal in all directions. So, this is where the extender comes to its place.

The placement of a device plays an important role when it comes to receiving a good quality signal. If you have placed the router in the living room, then the extender should also be placed in the same room. After the device gets configured, you can place the extender anywhere inside the home.

The power line on the other hand is recommended for having internet connectivity in a particular room. The signal through the power line is free from interference that occurs due to the walls or furniture. The average range of the powerline is approximately 300 meters.

Remember, don’t forget to check the quality of the internet available at home. The internet service provided by the internet service provider at home must be capable of delivering a min of 1 Mbps of data. If the speed of the internet is slow, then you have to go with a wireless range extender.

There are many range extender models available in the market. You need to select the one with more than one frequency band and 2 top antennas affixed.  There are many manufacturers in the market for range extenders but selecting the right brand can be a cumbersome project for an individual having limited knowledge. You can check the Netgear range extenders having the proper speed and coverage.

How To Configure The Wi-Fi Network Of An Extender Or Access Point To Automatically Connect To The Best Signal

When you opt for the Internet with a reputed ISP, they usually offer us a Wi-Fi router for free through which to connect both computers and other devices to the Internet, cable, and Wi-Fi. However, these routers, in general, are of very low range, so, in addition to not having many functions and being of very low performance, both the speed and the coverage of the Wi-Fi network usually leave quite a lot to wish.

While solving the problem of speed is quite complicated and happens to change the router or add another that takes care of Wi-Fi, if you are only interested in solving the problem of wireless network coverage. One of the simplest ways to solve it is by installing a WiFi extender or access point, a device that, placed where the router’s signal arrives well but begins to get lost, is responsible for repeating it so that it reaches the areas farthest from the router.

Depending on the device you install, it is possible that it directly copies the Wi-Fi data that must be repeated and forwards the signal as such, or that you have to configure the network manually to which you connect (Wi-Fi access point).

In the first case, you will not have to do anything, so simply connecting the device and linking it to the original router would already be repeating the signal with the same configuration as our router, however, if what you have installed has been a point of access, before making it work you must do the following.

How to create a Wi-Fi hotspot

The first thing to do is to access its configuration panel by connecting it directly by cable to the computer and accessing its IP from the browser.

Once inside the configuration panel, you must place yourselves on the Wi-Fi configuration section, and there you must configure the options as follows:

  • SSID or network name: The same on the router and access point.
  • Security, password, and encryption: The same on both devices.
  • Channel: Different on the router and access point.

Once you save the changes, you can see that now, although computers and mobiles show us a single network (the closest one), if you scan the wireless spectrum you can see that, in reality, there are two equal networks on different channels.

If you are using an Android/iOS smartphone or tablet, this device will automatically connect to the network that offers the best signal. If you are closer to the main router, you will connect to it, but if you move away, you will connect without having to walk to the access point. In case of using a Windows laptop, this system does not get along with network changes, so you will most likely have to disconnect and connect again to choose the network that arrives with the best signal depending on where you are.

If you configure the network incorrectly, although the configuration is most likely to work, surely you have two independent Wi-Fi networks so that you have to switch from one to another manually. This will happen if, for example, the two networks have different SSIDs or different passwords. If you configure them with the same channel, it will most likely not work since mobile devices will not know how to interpret the change.

How To Ensure “No More WiFi Dead Zones” In The House?

If you have installed a WiFi router in your house thinking it will get rid of internet connectivity issues in the house, then you are wrong. Your WiFi Router with top-rated internet service may not be good enough for covering all corners of your house. There are dead spots in every house where the Wi-Fi signal and internet speed either slows or completely disappear.

The signal strength reduces if there are walls, doors, and other obstructions between the router and the devices you want to access the internet. It is important for you to place the router at a central location in the house, which at times becomes difficult to do. If your router is kept in a cabinet or closet or at the far end of your house, then you will have to change its location. Also, keep it at a height and in open because that is how the signal strength from the router can be enhanced.

If you think that your router is incapable of transmitting power internet signals in every nook and cranny of the house, then you will have to get another device to do that. That device is a WiFi Extender. There are several brands, which are manufacturing WiFi Extenders, so you can buy the one that suits your requirements and budget the best.

However, buying an extender is just the half job done, as you will have to find steps on how to set up a WiFi Extender as well. If the extender is not properly set up, then you won’t be able to achieve the results that you have anticipated. Moreover, the placement of the extender is of paramount importance when it comes to ensuring the internet signal in all corners of the house.

As efficient as extenders may sound, there is one drawback in these devices as well, i.e., extenders are successful in small houses (2-3 BHK). If you have a bigger house, then you will have to go for a mesh router, which comprises of 3-4 devices that cover a big house with internet signals.

No matter what device you choose, an extender or mesh router, make sure to go for a branded product because only that ensures fast and reliable internet for a long period of time along with the elimination of WiFi dead zones.

How To Eliminate Wi-Fi Black Spots Around Your House?

Internet black spots are very frustrating during the lockdown because you want to send an email, post a status on Facebook or refresh your Twitter feed, but you can’t do any of these because of dead spots around the house. As if COVID 19 was not enough to annoy you, the absence of Wi-Fi signals is adding to your troubles.

When it comes to fixing the black spots, you can consider one of the following two solutions, which are a WiFi Extender or wireless mesh router. But, which solution is best for you? Let’s find out in this post.

Wi-Fi Router Placement

Before you proceed with the solution part, it is important that you should place the Wi-Fi router at the right spot. If you think your router is at the right spot, yet the internet is not working, then read on.

What is a mesh router system? And, what is a WiFi Extender?

Mesh Router system and WiFi Extender are the same things, but they work in slightly different ways.

WiFi Extender

A WiFi Extender picks up Wi-Fi signals originated from the router and passes them on to areas where internet signals used to remain absent. You can plug this device anywhere in the house and enjoy fast and seamless internet. The only downside to a WiFi Extender is that it behaves like a separate network, so your Wi-Fi enabled device has to switch from your main Wi-Fi to the extender with a different username and password. Moreover, there will be a drop in the signal as you go away from the extender.

Mesh Router System

This system involves multiple Wi-Fi Extenders, but they all are on the same network, thus letting you enjoy fast and seamless internet in all corners of the house without changing the username and password. Each mesh device connects to other mesh devices in the network instead of just going back to the main router as WiFi Extenders do.

A mesh network creates a much larger wireless footprint compared to a single router or the combination of router and extender. Your device comes to think as you have a large Wi-Fi area.

What is more suitable for you? WiFi Extender or Mesh Network?

Well, it depends upon your home and the way you want to use your Wi-Fi

Wi-Fi Extender is suitable for:

  1. Single-story houses.
  2. Small houses.
  3. Single Wi-Fi black spot.
  4. Few internet users.

There are many brands of WiFi Extenders available on the market, so you can buy the device that suits your requirements the best.

Wireless Mesh Network is suitable for:

  1. Old houses with thick walls.
  2. Multi-storeyed houses.
  3. Multiple Wi-Fi black spots.
  4. Multiple users.

You can also find a wide range of mesh routers on the market. If you need any assistance regarding the installation of the extender or mesh router, then you can get in touch with experts.

Can A Wireless Extender Help Reach Wireless Signals In Every Corner Of Your House?

The wireless router that comes with your internet service may not cover every corner of your house due to its limited range or connectivity. Almost in every house, there are dead spots where the Wi-Fi signal is approximately negligible or available with limited speed.

The placement of the router at the same time can’t be sidelined. Thus, if there are several walls or doors located in-between the router and the device, then the signal may not reach properly. If you move away from your router, the signal will continue to drop.

The router must be located in the center of your home but this is ideally not the case. If you have placed the router in some cabinet or closed surface, then take it out from there and place it in open.

If the Wi-Fi router is built into the internet service provider provided modem, then you can look for the wireless extender option, which creates additional Apps to help to reach the signal in every corner of the house.

Let’s discuss internet speeds. Don’t mix up slow wireless with a slow network plan.

What you are paying to the internet service provider is for getting the data at different speeds like if you opt for a 24 Mbps plan, then you will get a speed of 24 megabits per second. Likewise if you opt for 1000 Mbps, then you will get more speed at extra cost. You can’t get speeds faster than the one offered by ISP. If you are using the internet and your kids are playing games online, then the slow internet speed issue may encounter.

If you have subscribed for a high-speed internet pack and still getting the low signal, then you might be accessing the internet from an area with weak Wi-Fi coverage.

A range extender is a small device that plugs into the power outlet and extends the range of the internet in a particular area of your residence. It is recommended to use the same brand of the extender as your router. Check out more information on how to setup Wifi Extender to ensure strong and uninterrupted signals across the house.

There are several extenders available under $40 which can well enhance the range of the network. However, some of these can’t send or receive the signal at the same time. So, extenders work where internet access is limited or the price of the plan is low.

In best extenders, you will find multiple bands and radio frequencies to send and receive the signal simultaneously which can be better but not perfect. Some extenders even cost more than $100. You can consider the popular brands like Netgear, Linksys, Eero or Google for mesh Wi-Fi systems.

All these routers us two or more satellites that are placed throughout your home. You can place anywhere according to your requirement. The mesh routers communicate with each other and use different radio frequencies to route traffic and keep speeds constant throughout your house. If you need further support or assistance in this regard, you can stay in touch with the experts available online.

Working From Home: WiFi Extenders Are An Easy Way To Boost Coverage

Work from home is the latest work culture that we all have been forced to follow due to COVID-19 breakdown. Our homes are overrun by technology amid lockdown. While adults are trying to cope up with their backlog of work on their personal computers, children are also trying to study via several apps like Google Hangouts, Zoom, and many more. It is quite disappointing to see the dining room table turning into an overgrown IT department.

If you have been working from home for all these weeks, then you must have realized that there are certain spots in the house where the Wi-Fi signals remain totally absent. If there are such spots in the house, then you need to find a way to eliminate them using the right devices. You have to understand that many issues stem from Wi-Fi dead spots, like everybody sitting near the router to get the best internet signals, and if that router is kept in your room, then everybody will remain there, disturbing your privacy completely.

If you want to overcome this problem, then you will have to use a WiFI Extender because this is the only device that can get rid of problems like ‘Wi-Fi dead spots’. Wi-Fi routers usually end up in the corner of the house because that’s where the cable comes in. Now, if you have a highly efficient router with the fastest internet service, you may not be able to get the Wi-Fi coverage everywhere because of the limited coverage.

WiFi Extenders come in all shapes and sizes, as some are large while others are small, but none of those things matter, as WiFi Extenders can easily spread the Wi-Fi signals to every nook and cranny of the house, provided it has 2-3 rooms because extenders too have limited coverage. It is very easy to set up WiFi Range Extender, and once the extender is set up, you will find a significant change in the Wi-Fi signals. You just need to plug the WiFi Extender into a standard outlet and rotate the antennas to pull in the signals from your current router followed by boosting it to the rest of the home. The process of setting up an Extender looks like this:

  1. Plug the extender into an outlet close to the router. Turn it on and wait until the power light comes on.
  2. After that, you need to connect your smartphone’s Wi-Fi onto the new WiFi extender followed by opening a web browser.
  3. After that, you need to create a password that will let you log into the extender. Then, you should select the Wi-Fi signal in your house that you wish to extend.
  4. Now, you need to type in your Wi-Fi password for the original router. A few seconds later, your Wi-Fi extender will be connected.
  5. You need to find a spot to plug in your new WiFi Range Extender, which should be away from the router.
  6. Extenders have an indicator light that lets you know about the placement of the extender whether it is too close or too far from the router.
  7. It is better to place the extender close to the router, but not beyond the edge of your current coverage.

That sums up the extender setup process and now, you will see all the dead spots being enlightened by the Wi-Fi coverage.

Wifi Range Extender Or Mesh Router – Which Suits Your Home Network The Best?

With most people spending time at home these days, the requirement of the internet has risen exponentially, as everybody needs the internet to keep themselves entertained at this time of global emergency. People are forced to work from their homes using their computers and they require the internet at all times. With most homes having Wi-Fi networks, there is a problem that has come to the fore, which was somewhat hidden when things were normal.

The problem is that the Wi-Fi signals are limited to certain areas and people sitting beyond those areas are not able to access the internet. If you too are experiencing this particular issue, i.e., dead zones in some spots of your house, then you have a few options to eliminate dead zones such as WiFi Range Extender or Mesh Router, which has its own range-extending satellite devices known as nodes.

WiFi Range Extenders are the cheap and best option for smaller spaces, but if you have a big home, then you will have to opt for a mesh router because they can offer a comprehensive coverage through their nodes, which you can strategically place in different areas of the house. The only thing that matters in wireless networking is ‘Location’ because the wireless access points can only put out a network signal, which is equally strong as the incoming wireless signal that is being received from the router.

The best way is to check at the speed test data and then, finding the room closest to the dead zone where the internet signals are good. Doing this will help you find the right place for having the extender to cover the dead zone. It is always great to run a test speed on your network to know how much speed you are getting.

Use WiFi Range Extender for small dead zones

If you are living in a small house with two rooms, then you just need a WiFi Extender to extend the range of your wireless signal, and you can easily get an extender online. Check out the steps to know how to set up a WiFi Extender. Before buying an extender, just make sure it has the WPS button because that makes the setup process a lot easier. The drawback in almost all WiFi Extenders is that they don’t get to the max speed of your internet network, so you are going to get 50Mbps – 75Mbps, which is sufficient for online HD streaming, playing online video games and do other tasks. Just keep in mind that you need to find the room closest to the dead zone with the best internet signal because you’ll place the extender at that spot.

Use Mesh Routers for whole-home coverage

If there are multiple dead zones in your house, then you have to get a mesh router, which comes with nodes that you can place in different spots of the house to ensure that the entire house receives the best internet signals. The software of these mesh routers has a huge role to play in the functioning and setting up the algorithms to calculate the best way to route your connection as per your movements in the house. As you move from the range of one node to another, the premium-quality mesh router will automatically transfer your network to the strongest node without letting you know.

It is now up to you to decide whether you need a WiFi Extender or a mesh router. There is obviously a price difference between the two, as an extender will cost you 5x less than what a mesh router will, but then, the requirement plays a major role because an extender may not be able to cover a large house.

How To Access Internet Via Netgear WiFi Extender During Coronavirus Lockdown?

COVID-19 or Coronavirus as it is popularly called has brought the whole world on its knees. The entire world is under lockdown with thousands of people dying every day. The only way to work is by staying at home, which is why the importance of the internet has risen exponentially. I’m not saying it wasn’t before, but the internet is more important today than it ever was, as it is the only source of doing business or should I say, retaining business for people until the SARS CoV-II virus fully vanquishes.

The good thing is that in most parts of the world, the internet speed and quality are at satisfactory levels. At the same time, it can also be said that businesses that used to be carried out over the internet are the ones that are still being carried out, while others are being in shambles.

If you too are forced to sit inside your house and work on the internet, then that is better than sitting idle at home. However, many users are facing issues while accessing the internet due to signal range related issues. As many people only have routers at homes, which have a limited range, the issue is quite common to arise. If you want to get rid of this issue, then you got to install a WiFi Extender to extend the range of the Wi-Fi signals. You can buy N300 Extender because of its easy setup and incredible range and consistency. To know how to the steps for the Netgear WiFi Extender N300 setup, you can follow this link. The process is very simple and can be performed even by non-technical people.

When it comes to setting up an extender, you must keep in mind that there is a software aspect of the process as well. You will have to download Netgear Genie followed by performing Netgear Genie Smart setup, which involves entering the user credentials.

You need to know that Netgear Genie setup allows you to manage and control your extender in the easiest of ways, so make sure you have the app installed on a device where you can easily access it. Once you have configured your extender with Genie app, you can connect your devices with the extender’s network and you shall surf the web without any issues. Should you come across any issue, then you can get in touch with experts for quick and reliable assistance.